FERRICON is used in providing concrete floors, which has to carry heavy loads and traffic. This load causes Impact as well as abrades the floor topping. FERRICON being ductile and malleable resist this effect. It is available in 3 grades – i.e. Ferricon Metallic Floor Hardener, Ferricon NM – Non Metallic Floor Hardener and Ferricon QTZ – Quartz based Floor Hardener.

FERRICON provides the following important features to the concrete surface:

• * Wear Resistant,
• * Spark Resistant
• * Non Dusting,
• * Easy to clean
• * Non-Slip,
• * Oil proof
• * Excellent resistance to dragging scraping point loads.
• * Extends serviceable life of the concrete floor.
• * Easy and economical to apply
• * Having hardness more than 8 to 9

Industrial Floors, Run-Ways, Damp,-Spill Ways, Godown Floors, Ware Houses, Railway Platform, Shopping Centers Loading Bays, Trucking Lanes, Car Parks, Repair Workshops, Machine Shops, Ramps, Sliding & Rolling Work Places, Forklift Truck Movement, Crawler Tractor Traffic & Transporting Equipment with Steel Wheels, Taxi-ways, Weirs, Garage Floors, Parking Aprons, Jetty, Docks & Quays, Foundry Floors, Hangers, Duct & Silos, Concrete Roads, Causeways, etc.

FERRICON – NM is a very hard, non slip aggregate comprised of quality controlled, factory blended pure graded emery and special additives to improve workability.

Emery is a natural occurring mined material that is extremely hard, tough and abrasion resistant. As a result, proper installation of FERRICON – NM will impart long life and excellent skid resistance for concrete surfaces. FERRICON – NM is completely non corrosive used for inside and outside.

FERRICON-QTZ is a ready-to-use non-metallic floor hardener comprised of finely graded quartz aggregates, special additives and Portland cement. Proper installation of FERRICON-QTZ will impart long life and high durability to concrete floors. It can be used inside or outside and is completely none rusting.

Florseal-LI is a lithium silicate based concrete densifier/hardener. florseal-li penetrates into the pores of concrete surfaces where it can chemically reacts with the available lime to produce insoluble calcium silicate hydrate which densify and harden the surface from within and gives high abrasion resistance and dust proof floor.

Florseal-LI is a lithium silicate based concrete densifier/hardener. florseal-li penetrates into the pores of concrete surfaces where it can chemically reacts with the available lime to produce insoluble calcium silicate hydrate which densify and harden the surface from within and gives high abrasion resistance and dust proof floor.

It is a mineral based floor-patching compound having high strength. The repaired surface could be put in to use on the next day and does not need any curing.

• Set hard in few hours
• Can be used to a thickness of 15mm
• Needs no curing
• Adheres to any surface
• Stronger than concrete
• Abrasion resistant

CONBOND-A is latex based polymer used for bonding a freshly laid concrete to old surfaces like concrete, masonry, wood etc even of a minimum thickness of 10 mm. It has got high impact strength. It requires very less curing.

CONBOND-A modified cement mortar is having almost double shear, tensile, compressive, flexural and impact strength than that of unmodified (ordinary cement) mortars and properties of good resistance against U/V rays as well as protection against salt water.

• Where the top skin or laitance of concrete is eroded.
• Bonding new to old set concrete.
• Providing concrete topping of lesser thickness on the existing surface.
• Repairing worn-out floor.
• For featheredge leveling.
• For sealing the construction joints.
• Repairing pre-stressed & precast concrete members.

• High bonding strength with concrete, stone, brick, wood etc.
• Repairs could be made even to a thickness of 10 mm.
• Makes the mortar more cohesive with less W/c.
• Non toxic.
• Increases the mechanical strength of mortar.
• Makes the mortar waterproof, restrain cracking, minimizes wear and tearv.
• Desired pigment could be used to get matching shade.
• Could be used on wet areas.
• Very less or no curing is required.

CONMAST is a thermo plastic compound of selected fillers and blown grade Bitumen in powder form. When it is heated at about 200-300o C, the entire mass transforms into a sticky paste that could be trowelled easily on the surface. The treated surface is resistant to most diluted inorganic acid.

FERROX GROUT – Free flow, high strength, non-shrink, cementatious precision grout having strength of 75 Mpa which imparts controlled expansion in the plastic states whilst minimizing the water demand. Ferrox Grout is a blend of Portland cement, Graded Fillers & Chemical additive supplied in a ready to use dry powder, only water should be added at site. It develops high early compressive and flexural strength without the use of chlorides.

• Cement, Textile, Granite & Paper Plant Machinery.
• Diesel Generators & Crane
• Machine Foundation & Building Works
• Heavy Steel Structure Foundation
• Heavy Reciprocating Equipment
• Compressors, Pump Sets
• Steel Rolling Mill Beds
• Turbo generators
• Pulverizing Mills